VOLVO
ECM-433B - Leak diagnostic unit, pump. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module receives no signal from the leak diagnostic pump, and the fault code is set. The fault can be caused by poor contact, an open circuit in the signal or supply wire, or a damaged pump. The leak diagnostic is switched off while the fault is present.
Possible causes
- Contact resistance in the connections
- Open circuit in the signal wire
- Open circuit in the supply wire
- Damaged pump in the leak diagnostic unit
What you can do
- 1Check the connector of the leak diagnostic unit for contact resistance and oxidation
- 2Use a multimeter to check that the signal and supply wires are not open-circuited
- 3Look for chafed or pinched wiring to the leak diagnostic unit
- 4Have you got a diagnostic tool: check in live data that the pump signal is present when the leak diagnostic runs
- 5Have a workshop replace the pump in the leak diagnostic unit if the wiring is intact but the signal is still missing
Symptoms you may notice1
- Malfunction indicator lamp (MIL) is on
What the fault can affect1
- The leak diagnostic is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.