VOLVO
ECM-4480 - EGR position sensor. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module monitors the signal from the position sensor on the EGR valve. The code is set when the signal is judged to be incorrect, and EGR control then stops. The fault can lie in the connectors, the signal wire, the supply to the sensor or the sensor itself.
Possible causes
- Poor contact, contact resistance or oxidation in the connections, or a break in them
- Break in the signal wire from the position sensor
- No voltage supply to the position sensor
- Damaged position sensor
- Position sensor has stopped working
- Electromagnetic interference can sometimes have triggered the code
What you can do
- 1Note the fault code, erase it and test-drive to see whether it returns
- 2Check that the EGR valve can be closed and opened fully without sticking, since a sticking valve can give the same code
- 3If you have a diagnostic tool: activate the EGR valve several times and see whether it moves more freely afterwards
- 4Check the position sensor connector for contact resistance and oxidation, and look for a break in the signal wire
- 5If the fault remains, have a workshop with diagnostic equipment measure the supply and signal to the position sensor
Symptoms you may notice1
- Message shown in the text display
What the fault can affect1
- No EGR control takes place
General guidance for car owners. Diagnosis on the car can point to a different cause.