VOLVO
ECM-56AA - Oil quality, level and temp sensor. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module (ECM) monitors oil level, oil temperature and oil quality through one combined sensor. The code is set when the PWM signal from that sensor is faulty. The cause may be wiring with a break or short, or poor contact. The driver normally does not notice the fault.
Possible causes
- Break or short to voltage in the supply wire
- Break or short to voltage in the signal wire
- Raised contact resistance or oxidation in the connections
- Damaged oil level sensor
- Supply wire shorted to ground
- Signal wire shorted to ground, or briefly broken
What you can do
- 1Check that the relevant fuses are intact
- 2Check that the connector at the sensor is fully seated and free from oxidation and contact resistance
- 3With a multimeter, check that the supply and signal wires have no contact with ground or voltage and are not broken
- 4If you have a diagnostic tool, read the oil level, oil temperature and oil quality values in live data with the ignition on and see whether anything looks wrong
- 5If the fault remains, have a workshop check the wiring and replace the sensor if needed
Symptoms you may notice1
- No noticeable symptoms for the driver
General guidance for car owners. Diagnosis on the car can point to a different cause.