VOLVO
ECM-580F - Configuration fault. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module (ECM) gets setup data for the car over CAN from the central electronic module (CEM). The code is set when that signal is missing or faulty. Causes may be CAN faults, connector problems, or a used CEM that does not suit the car. The driver normally does not notice the fault.
Possible causes
- Signal from the CEM is missing or faulty
- Raised contact resistance or oxidation in the connector terminals
- Break in the CAN wiring to the central electronic module (CEM)
- Internal fault in another module on the same part of the CAN network
- CAN-related fault codes stored in the CEM
- The central electronic module (CEM) is not intended for this car, for example if a used module with other software or hardware has been fitted
What you can do
- 1Read the CAN-related codes in the central electronic module (CEM) and fix them first
- 2Check that the connectors on the CAN network between the modules are fully seated and free from oxidation
- 3With a multimeter, check that the CAN wires are not broken
- 4If the car has been fitted with a used control module, have a workshop check that it is right for the car
Symptoms you may notice1
- No noticeable symptoms for the driver
General guidance for car owners. Diagnosis on the car can point to a different cause.