VOLVO
ECM-6000 - Air condition. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
8 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (20)
- Volvo C30 (2007–2013)2007Engine D5244T8, D5244T9 only
- Volvo C30 (2007–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2007Engine D5244T8, D5244T9 only
- Volvo C70 (2006–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2006Engine D5244T8 only
- Volvo S40 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo S40 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo S60 (2001–2009)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo S60 (2001–2009)2007–2009Engine D5244T4, D5244T5, D5244T7 only
- Volvo V50 (2004–2013)2006Engine D5244T8 only
- Volvo V50 (2004–2013)2007Engine D5244T8, D5244T9 only
- Volvo V50 (2004–2013)2008–2010Engine D5244T13, D5244T8, D5244T9 only
- Volvo V70 (2000–2008)2006Engine D5244T4, D5244T5, D5244T6, D5244T7 only
- Volvo V70 (2000–2008)2007Engine D5244T4, D5244T5, D5244T7 only
- Volvo V70 (2000–2008)2008Engine D5244T5, D5244T7 only
- Volvo V70 XC / XC70 (2001–2007)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2006–2007Engine D5244T4 only
- Volvo XC90 (2003–)2008–2010Engine D5244T4, D5244T5 only
- Volvo XC90 (2003–)2011Engine D5244T18, D5244T4, D5244T5 only
- Volvo XC90 (2003–)2012All engines except: B5254T2, B6324S5
What does this fault code mean?
The engine control module (ECM) monitors the signal to the air conditioning (A/C) system. The code is set if the signal is too high, too low or missing. At high torque output the ECM can switch off the A/C function, and then the A/C does not work.
Possible causes
- Contact resistance or oxidation in the terminals and connectors
- Open circuit in the signal cable
- Signal cable short-circuited to ground
- Signal cable short-circuited to supply voltage
- Damaged A/C relay
What you can do
- 1Check that the A/C relay is firmly seated in its holder and that its contacts are clean and tight
- 2Look for loose, corroded or oxidised connectors at the A/C relay and at the control module connector, and clean or firmly reseat them
- 3Use a multimeter to check that the signal cable is neither broken nor in contact with ground or voltage
- 4If you have a diagnostic tool: activate the A/C relay and listen for it to click
- 5If nothing above finds the cause, have a workshop with diagnostic equipment check the signal from the control module
Symptoms you may notice2
- Message in the information display
- The A/C system does not work
General guidance for car owners. Diagnosis on the car can point to a different cause.