VOLVO
ECM-9210 - Electronic throttle unit, potentiometer 1. Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
This fault code has different meanings depending on model, model year or engine. Select the meaning that applies to your car.
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module (ECM) monitors the signal from potentiometer 1, the first throttle position sensor in the throttle unit. If that signal is faulty, the code is set. The cause can be poor contact, signal cables short-circuited to each other, or a damaged throttle unit.
Possible causes
- Contact resistance or oxidation in the connectors between the ECM and the throttle unit
- Signal cables shorted together
- Damaged throttle unit
What you can do
- 1Check the connectors between the ECM and the throttle unit for contact resistance and oxidation
- 2Use a multimeter to check that the signal cables are not short-circuited to each other
- 3If nothing is found and the code returns as permanent, the throttle unit may need replacing by a workshop, which also carries out the adaptation
- 4If you have a diagnostic tool: follow the throttle position from potentiometer 1 in live data and check that the value follows the accelerator pedal smoothly
Symptoms you may notice1
- The car's performance is reduced
What the fault can affect2
- Potentiometer 2 is used to work out the throttle angle
- If both potentiometers fail at once, the throttle motor loses its supply and the throttle returns to its spring position
General guidance for car owners. Diagnosis on the car can point to a different cause.