VOLVO
ECM-921C - Electronic throttle unit, potentiometer 1. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The engine control module (ECM) has registered that the signal from potentiometer 1, the first throttle position sensor, is too high, and the code is set. The cause can be poor contact, an open or voltage-shorted signal cable, or an open earth lead to the potentiometers.
Possible causes
- Contact resistance or oxidation between the ECM and the throttle unit
- Signal cable has an open circuit or is short-circuited to voltage
- Open circuit in the earth lead to potentiometers 1 and 2
- Damaged throttle unit
What you can do
- 1Check the connectors between the ECM and the throttle unit for contact resistance and oxidation
- 2Use a multimeter to check that the earth lead to the throttle unit potentiometers has no open circuit
- 3Use a multimeter to check that the signal cable has no open circuit and is not short-circuited to voltage
- 4If nothing is found and the code returns as permanent, have a workshop replace the throttle unit and carry out the adaptation
Symptoms you may notice1
- The engine responds to the accelerator less well than normal
What the fault can affect2
- Potentiometer 2 takes over the throttle angle calculation
- When potentiometers 1 and 2 both report faults together, the throttle motor loses its supply and the throttle returns to rest
General guidance for car owners. Diagnosis on the car can point to a different cause.