VOLVO
ECM-9240 - Engine control module (ECM). Faulty signal
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
The ECM has logged a fault inside itself, or a fault in the circuit to the throttle damper motor, and sets the code. The cause can be poor connections, open or short-circuited wiring to the damper motor, a damaged throttle unit, or a damaged ECM.
Possible causes
- Contact resistance or oxidation in the connectors between the ECM and the throttle unit
- Open circuit or short-circuit to ground or voltage in the wiring to the damper motor
- The wiring to the damper motor is short-circuited to each other
- Damaged throttle unit
- Damaged engine control module
What you can do
- 1Read off the fault codes and first remedy any that concern the throttle unit or the throttle position sensor, if they are stored
- 2Check the connectors between the ECM and the throttle unit for contact resistance and oxidation
- 3Use a multimeter to check that the damper motor wires have no open circuit and are not short-circuited to ground, voltage or each other
- 4If the fault stays permanent after these checks, a workshop may need to replace the throttle unit. Any replacement of the throttle unit or ECM needs an adaptation by a workshop.
Symptoms you may notice3
- The Check engine lamp lights
- The car's performance is reduced
- The idle is uneven
What the fault can affect1
- The ECM switches off the supply to the throttle motor, and the throttle moves to its spring-returned position
General guidance for car owners. Diagnosis on the car can point to a different cause.