VOLVO
ECM-930B - Control module communication problems. Signal missing
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
9 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2001–2009), S80 (1999–2006), V50 (2004–2013), V70 (2000–2008), V70 XC / XC70 (2001–2007), XC90 (2003–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2007Engine B5254T3 only
- Volvo C30 (2007–2013)2008–2013Engine B5254T7 only
- Volvo C70 (2006–2013)2006–2007Engine B5254T3 only
- Volvo C70 (2006–2013)2008–2013Engine B5254T7 only
- Volvo S40 (2004–2013)2005–2007Engine B5254T3 only
- Volvo S40 (2004–2013)2008Engine B5254T3, B5254T7 only
- Volvo S40 (2004–2013)2009–2012Engine B5254T7 only
- Volvo S60 (2001–2009)2005–2006Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo S60 (2001–2009)2008–2009Engine B5204T5, B5244T5, B5254T2 only
- Volvo S80 (1999–2006)2005–2006Engine B5204T5, B5244T4, B5254T2, B6294S2, B6294T only
- Volvo V50 (2004–2013)2005–2007Engine B5254T3 only
- Volvo V50 (2004–2013)2008–2012Engine B5254T7 only
- Volvo V70 (2000–2008)2005Engine B5204T5, B5244T4, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2006–2007Engine B5204T5, B5244T5, B5254T2, B5254T4 only
- Volvo V70 (2000–2008)2008Engine B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2005All engines except: D5244T
- Volvo V70 XC / XC70 (2001–2007)2006Engine B5244T4, B5254T2 only
- Volvo V70 XC / XC70 (2001–2007)2007Engine B5254T2 only
- Volvo XC90 (2003–)2005–2006Engine B5254T2, B6294T only
- Volvo XC90 (2003–)2007–2012Engine B5254T2 only
- Volvo XC90 (2003–)2013–2014Engine B5254T9 only
- Volvo XC90 (2003–)2015
What does this fault code mean?
Although the code is titled signal missing, it concerns a fault the ECM has registered on the steering wheel module (SWM) or on its CAN link. The fault may also lie in the CEM, BCM or TCM, or in the wiring between them.
Possible causes
- The cause may lie in the steering wheel module (SWM)
- The cause may lie in the central electronic module (CEM)
- Open circuit in a CAN wire
- Short circuit between the CAN wires
- The ECM itself has an internal fault
- Internal fault in another module on the same part of the CAN network
What you can do
- 1Read the fault codes in the CEM and other affected modules first. The code should not be cleared until those are remedied
- 2Then read the steering wheel module (SWM) fault codes and deal with them
- 3Check the CAN wires for breaks and chafing. Use a multimeter to see whether any wire is open or shorted to another
- 4If you have a diagnostic tool: see whether the steering wheel module responds when read with the ignition on, and whether the cruise control buttons register
- 5If the fault remains once the other codes are remedied, have a workshop with diagnostic equipment decide where the fault sits
Symptoms you may notice1
- Cruise control does not function at all
What the fault can affect1
- Cruise control is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.