VOLVO
ECM-P001621 - Crankshaft Position - Camshaft Position Correlation - Bank 1 Sensor A. General Signal Failures. Signal too low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
10 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Show models by year and engine (32)
- Volvo S60 (2011–)2011–2012Engine B6304T4 only
- Volvo S60 (2011–)2013Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T4 only
- Volvo S60 (2011–)2014Engine B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4 only
- Volvo S60 (2011–)2015All engines except: B4164T, B4164T2, B4164T3, D4162T, D4204T5, D5204T3, D5204T7, D5244T11, D5244T15, D5244T23
- Volvo S80 (2007–)2010Engine B6304T2, B6324S, B6324S2, B8444S only
- Volvo S80 (2007–)2011Engine B6304T4, B6324S4, B6324S5, B8444S only
- Volvo S80 (2007–)2012Engine B6304T4, B6324S4, B6324S5 only
- Volvo S80 (2007–)2013Engine B5254T12, B5254T14, B6304T4, B6324S4, B6324S5 only
- Volvo S80 (2007–)2014Engine B4204T11, B4204T12, B4204T15, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5 only
- Volvo S80 (2007–)2015All engines except: B4164T, D4162T, D4204T5, D5204T3, D5244T15
- Volvo V40 (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 (2013–)2015Engine B4204T11, B5204T8, B5204T9 only
- Volvo V40 Cross Country (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 Cross Country (2013–)2015All engines except: B4164T, D4162T, D4204T14, D5204T6
- Volvo V60 (2011–)2011–2012Engine B6304T4 only
- Volvo V60 (2011–)2013Engine B5204T8, B5204T9, B6304T4 only
- Volvo V60 (2011–)2014Engine B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12, B6304T4 only
- Volvo V60 (2011–)2015Engine B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B6304T3, B6304T4, B6304T5 only
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo V70 (2008–)2011–2012Engine B6304T4, B6324S5 only
- Volvo V70 (2008–)2013Engine B5204T9, B6304T4, B6324S5 only
- Volvo V70 (2008–)2014Engine B4204T11, B5204T9, B6304T4, B6324S5 only
- Volvo V70 (2008–)2015Engine B4204T11, B5204T9, B6304T4 only
- Volvo XC60 (2009–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo XC60 (2009–)2011–2013Engine B6304T4, B6324S4, B6324S5 only
- Volvo XC60 (2009–)2014Engine B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B6304T4, B6324S4, B6324S5 only
- Volvo XC60 (2009–)2015All engines except: B4204T7, D4204T5, D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23
- Volvo XC70 (2008–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo XC70 (2008–)2011–2013Engine B6304T4, B6324S4, B6324S5 only
- Volvo XC70 (2008–)2014–2015Engine B4204T11, B6304T4, B6324S4, B6324S5 only
- Volvo XC90 (2003–)2011–2014Engine B6324S5 only
What does this fault code mean?
The engine control module checks the camshaft position against the crankshaft position and adjusts the camshaft adaptation. The code concerns bank 1, sensor A, and is set when the adaptation value falls below a limit. Adaptation is carried out during engine braking, and the code is checked after it has been completed.
Possible causes
- Incorrectly set camshafts
- Damaged VVT unit
- Poor quality engine oil
- Faulty camshaft control valve
- Damaged or worn timing chain
What you can do
- 1Read the code and note whether it is active right now or only stored
- 2If you have a diagnostic tool: read the camshaft adaptation and timing angle in live data with the engine running, and compare with the target value
- 3Check the engine oil level and that the oil is clean and of the right quality
- 4Have a workshop remove the control valve for cleaning and check the oil passages in the cylinder head, or fit a new valve
- 5If the fault returns: have a workshop check the camshaft basic setting and the VVT unit
Symptoms you may notice5
- The car lacks power when pulling away from standstill
- Engine is hard to start and cranks slowly
- Uneven idle
- Engine stalls while driving
- Check engine lamp lit or behaving abnormally
What the fault can affect1
- The control module uses a fixed value for the camshaft adaptation
General guidance for car owners. Diagnosis on the car can point to a different cause.