VOLVO
ECM-P003013 - HO2S Heater Control Circuit (Bank 1, Sensor 1). General Electrical Failures. Circuit open
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module controls the heating of the front lambda sensor on bank 1 by pulsing the current to the sensor's PTC element. The code concerns an open circuit and is set when the signal falls below a certain level while the heating is switched off.
Possible causes
- Poor contact and oxidation in the connections
- Open circuit in the supply from the system relay
- Faulty front lambda sensor
What you can do
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the connector at the bank 1 lambda sensor for poor contact and oxidation, and do not use rust-release spray or grease in the connector
- 3Use a multimeter to check that the supply voltage between the system relay and the lambda sensor has no open circuit
- 4Have a workshop measure from the back of the connectors, so they are not damaged and do not develop loose contact later
- 5If troubleshooting does not solve the fault: have a workshop try a new lambda sensor
Symptoms you may notice1
- Check engine lamp lit or behaving abnormally
What the fault can affect1
- Lambda control is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.