VOLVO
ECM-P003613 - HO2S Heater Control Circuit (Bank 1, Sensor 2). General Electrical Failures. Circuit open
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module regulates the heating of the rear lambda sensor on bank 1, sensor 2, by pulsing the current to the sensor's PTC element. The code concerns an open circuit and is set when the signal falls below a set level while the heating is switched off.
Possible causes
- Poor contact and oxidation in the connections
- Open circuit in the supply from the system relay
- Faulty rear lambda sensor
What you can do
- 1Read the code, clear it and road test the car to see whether it returns
- 2Check the connector at the rear lambda sensor for poor contact or oxidation, and do not use rust-release spray or grease in the connector
- 3Use a multimeter to check that the supply voltage from the system relay to the rear lambda sensor has no open circuit
- 4Have a workshop check the resistance of the lambda sensor
- 5If troubleshooting does not solve the fault: have a workshop try a new lambda sensor
Symptoms you may notice1
- Check engine lamp lit or behaving abnormally
What the fault can affect1
- Lambda control is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.