VOLVO
ECM-P003711 - HO2S Heater Control Circuit Low (Bank 1, Sensor 2). General Electrical Failures. Circuit short to ground
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module regulates the heating of the rear lambda sensor on bank 1, sensor 2, and sets the code when the signal falls below a set level while the heating is switched off. The fault is an electrical short to ground in the heater circuit, and lambda control is switched off.
Possible causes
- Signal wire shorted to ground
- Faulty rear lambda sensor
What you can do
- 1Read the code, clear it and road test the car to see whether it returns
- 2Use a multimeter to check that the wire to the rear lambda sensor is not shorted to ground
- 3Check the connector at the lambda sensor, and do not use rust-release spray or grease in the connector
- 4Have a workshop check the resistance of the lambda sensor, and replace it if it is damaged
Symptoms you may notice1
- Check engine lamp lit or behaving abnormally
What the fault can affect1
- Lambda control is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.