VOLVO
ECM-P00541B - HO2S Heater Resistance (Bank 1, Sensor 2). General Electrical Failures. Circuit resistance above threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The code is set when the engine control module registers that the rear oxygen sensor on bank 1, sensor 2, has not reached normal operating temperature. The fault concerns too high resistance, and the causes are contact resistance in the connectors or a damaged sensor.
Possible causes
- Contact resistance and oxidation in the connectors
- Damaged rear heated oxygen sensor
What you can do
- 1Look for contact resistance and oxidation in the connector to the rear oxygen sensor (bank 1 sensor 2), and correct what you find
- 2Read the fault code with a diagnostic tool and note whether it is active
- 3Make sure the fuses are intact. Their location is in the instruction manual
- 4With a multimeter, check that the wiring to the sensor has no open circuit
- 5If the connector gave no result, a new oxygen sensor is the next step
Symptoms you may notice1
- The Check engine (malfunction indicator) lamp lights up or behaves abnormally
General guidance for car owners. Diagnosis on the car can point to a different cause.