VOLVO
ECM-P006922 - MAP - Barometric Pressure Correlation. General Signal Failures. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
When the ignition is switched on before starting, the engine control module checks that the boost, air and ambient pressure sensors show about the same value. The code is set when the boost pressure sensor differs from the other two, and here its signal is too high.
Possible causes
- The boost pressure sensor (MAP) is damaged
What you can do
- 1With a diagnostic tool, compare boost and air pressure in live data before starting. If boost reads clearly above the other two, suspect the sensor
- 2If the air pressure sensor reading does not match the ambient pressure, the sensor may be damaged and need replacing
- 3Check the connector and wiring to the boost pressure sensor for looseness and oxidation
- 4Read the fault code with a diagnostic tool and note whether it is active
- 5Have a workshop check the boost pressure sensor if the fault remains after checking the connector and wiring
Symptoms you may notice1
- No noticeable symptoms for the driver
What the fault can affect1
- The engine control module uses a calculated value instead
General guidance for car owners. Diagnosis on the car can point to a different cause.