VOLVO
ECM-P007D12 - Charge Air Cooler Temperature Sensor Circuit High (Bank 1). General Electrical Failures. Circuit short to battery
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The boost pressure sensor (TMAP) measures boost pressure and temperature at the charge air cooler. The fault code is set when the signal from the sensor is above a limit. The cause can be a signal wire shorted to voltage, an open circuit in the signal wire or a damaged sensor.
Possible causes
- Open circuit in the signal wire to the boost pressure sensor
- Signal wire shorted to voltage
- Damaged boost pressure sensor (TMAP)
What you can do
- 1Use a multimeter to check that the signal wire to the boost pressure sensor has no voltage with the ignition off
- 2Check that the sensor connector is secure and not damaged
- 3Look for wiring that appears chafed or pinched at the sensor and along the route to it
- 4If you have a diagnostic tool: read the boost pressure sensor temperature in live data with the engine running and check whether it reads an unreasonably high value
- 5Have a workshop check the sensor if the wiring is intact and the fault remains
Symptoms you may notice1
- The Check engine warning lamp lights up
What the fault can affect1
- The engine control module uses a calculated value instead of the measured temperature
General guidance for car owners. Diagnosis on the car can point to a different cause.