VOLVO
ECM-P008000 - Exhaust Valve Control Circuit High (Bank 1). General Failure Information. No sub type information
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
10 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Show models by year and engine (28)
- Volvo S60 (2011–)2011–2012Engine B5254T5 only
- Volvo S60 (2011–)2013Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo S60 (2011–)2014–2015Engine B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo S80 (2007–)2007–2008Engine B5254T6, B8444S only
- Volvo S80 (2007–)2009Engine B5254T6, B5254T8, B8444S only
- Volvo S80 (2007–)2010–2011Engine B5254T10, B5254T11, B5254T8, B8444S only
- Volvo S80 (2007–)2012Engine B5254T10 only
- Volvo S80 (2007–)2013Engine B5254T12, B5254T14 only
- Volvo S80 (2007–)2014Engine B4204T11, B4204T12, B4204T15, B5254T12, B5254T14 only
- Volvo S80 (2007–)2015Engine B4204T11, B4204T12, B4204T15 only
- Volvo V40 (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 (2013–)2015Engine B4204T11, B5204T8, B5204T9 only
- Volvo V40 Cross Country (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 Cross Country (2013–)2015All engines except: B4164T, D4162T, D4204T14, D5204T6
- Volvo V60 (2011–)2013Engine B5204T8, B5204T9 only
- Volvo V60 (2011–)2014Engine B4204T11, B4204T12, B4204T15, B4204T9, B5204T8, B5204T9, B5254T12 only
- Volvo V60 (2011–)2015Engine B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12 only
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008Engine B5254T6 only
- Volvo V70 (2008–)2009Engine B5254T6, B5254T8 only
- Volvo V70 (2008–)2010–2011Engine B5254T10, B5254T11 only
- Volvo V70 (2008–)2012Engine B5254T10 only
- Volvo V70 (2008–)2013Engine B5204T9 only
- Volvo V70 (2008–)2014–2015Engine B4204T11, B5204T9 only
- Volvo XC60 (2009–)2014Engine B4204T10, B4204T11, B4204T12, B4204T15, B4204T9 only
- Volvo XC60 (2009–)2015Engine B4204T10, B4204T11, B4204T12, B4204T15, B4204T9, B5204T9, B5254T12, B5254T14 only
- Volvo XC70 (2008–)2014–2015Engine B4204T11 only
- Volvo XC90 (2003–)2005–2011Engine B8444S only
What does this fault code mean?
The engine control module (ECM) adjusts the exhaust camshaft position with a changeover valve on bank 1, the cylinder row nearest the front. The fault code is set when the control signal to the valve is too high. The causes are a signal wire shorted to voltage or a damaged valve.
Possible causes
- Signal wire to the changeover valve shorted to voltage
- Damaged exhaust camshaft changeover valve
What you can do
- 1Read off the fault code and check whether the fault is active right now or has only been present earlier
- 2Check that the fuses for the engine control circuits are intact
- 3Use a multimeter to check whether the signal wire to the exhaust valve has contact with voltage with the ignition off
- 4Check the connector at the exhaust valve and the wiring leading to it
- 5If you have a diagnostic tool, activate the exhaust valve and listen or feel for it responding
- 6If the fault returns after these checks, have a workshop check the valve
Symptoms you may notice4
- Check engine lamp (MIL) lights up
- Uneven idle
- Poor performance and lack of power
- The engine can stall while driving, during acceleration, deceleration or at steady speed
What the fault can affect1
- Exhaust camshaft control is switched off
General guidance for car owners. Diagnosis on the car can point to a different cause.