VOLVO
ECM-P008753 - Fuel Rail/System Pressure - Too Low. System Programming Failures. Deactivated
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
This fault code concerns the high-pressure side of the fuel system. It is set when the measured fuel pressure is too low compared with the target value while the engine is cold and the catalyst is warming up. The code is marked as deactivated in the control module programming.
Possible causes
- Leak in the fuel system
- Contact resistance or oxidation in the connections
- Signal wire shorted to voltage
- Open circuit in the signal wire or the signal ground wire
- Damaged fuel pressure sensor
- Damaged fuel pump
What you can do
- 1Make sure there is enough fuel in the tank
- 2Check the fuel lines for leaks
- 3Check the connectors at the fuel pressure sensor and the fuel pump for oxidation and loose contacts
- 4If you have a diagnostic tool: read the fuel pressure in live data when the engine is cold and compare it with the reading when warm
- 5Have a workshop with diagnostic equipment check that the fault code belongs to the correct programming, since it is deactivated
Symptoms you may notice3
- Check engine lamp (MIL) lights up
- Uneven idle
- The engine may hesitate, surge or run jerkily while driving
General guidance for car owners. Diagnosis on the car can point to a different cause.