VOLVO
ECM-P008862 - Fuel Rail/System Pressure - Too High. Algorithm Based Failures. Signal compare failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
This fault code concerns two values that do not agree on the high-pressure side of the fuel system: the measured fuel pressure and the target value the control module requests. It is set when the measured pressure is too high compared with the target.
Possible causes
- Clogged fuel system
- Contact resistance or oxidation in the connections
- Signal wire shorted to voltage
- Open circuit in the signal wire or the signal ground wire
- Damaged fuel pressure sensor
- Damaged fuel pump
What you can do
- 1Check the fuel lines and fuel filter for blockage
- 2Check the connector to the fuel pressure sensor for oxidation and looseness
- 3Use a multimeter to check that the signal wire to the fuel pressure sensor is not shorted to voltage
- 4If you have a diagnostic tool: read the fuel pressure in live data and see whether it rises too high compared with what the control module requests
- 5Have a workshop check the fuel pump and the fuel pressure sensor if the fault returns
Symptoms you may notice3
- The Check engine warning lamp lights up
- Uneven idle
- The car may hesitate or surge at times while driving
General guidance for car owners. Diagnosis on the car can point to a different cause.