VOLVO
ECM-P008B22 - Low Pressure Fuel System Pressure - Too High. General Signal Failures. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) requests a fuel pressure and controls the fuel pump through the fuel pump control module. The fault code is set when the pressure reported by the sensor is too high compared with the requested pressure for a certain time, while the engine runs. The cause can be a supply wire shorted to voltage, or a damaged sensor or pump control module.
Possible causes
- Supply wire to the fuel pump shorted to voltage
- Damaged fuel pressure sensor
- Damaged fuel pump control module
What you can do
- 1Use a multimeter to check that the supply wire to the fuel pump has no voltage with the ignition off
- 2Make sure the connectors to the fuel pump and the sensor are secure and clean
- 3If you have a diagnostic tool: compare the fuel pressure in live data with the requested pressure while the engine runs
- 4Have a workshop measure the fuel pressure with a gauge and, if it is wrong, check the sensor and the fuel pump control module
Symptoms you may notice3
- Check engine lamp (MIL) lights up
- The car lacks power and performs poorly
- The engine can stall while driving
General guidance for car owners. Diagnosis on the car can point to a different cause.