VOLVO
ECM-P00CF62 - Barometric Pressure - Turbocharger/Supercharger Boost Sensor "A" Correlation. Algorithm Based Failures. Signal compare failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM reads the output of the boost pressure sensor. If the boost sensor reading sits inside its usual band yet is lower than a value calculated from the barometric pressure sensor, the code is stored. The result is that boost pressure is limited, so the engine produces less power.
Possible causes
- Contact resistance or corrosion in the connections
- Boost pressure sensor is loose
- Boost pressure sensor is damaged
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2Check the connector at the boost pressure sensor: it should be fully engaged and free from corrosion
- 3Check that the boost pressure sensor is firmly seated in its mounting and has not come loose
- 4If you have diagnostic equipment, with the ignition on the boost pressure should show roughly the same value as atmospheric pressure, and with the engine idling it should read lower
- 5If the fault remains and the sensor is damaged, have a workshop replace the boost pressure sensor
Symptoms you may notice2
- The car runs poorly and lacks power
- Engine warning lamp (check engine) lit or behaving abnormally
What the fault can affect1
- Boost pressure is limited
General guidance for car owners. Diagnosis on the car can point to a different cause.