VOLVO
ECM-P010662 - Manifold Absolute Pressure/BARO Sensor Range/Performance. Algorithm Based Failures. Signal compare failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM measures the intake pressure with an air pressure sensor and compares it with a value worked out from a model. The code is stored when the sensor reading is too high compared with the model. It is a comparison failure between the sensor signal and the model, and the control module then works with a fixed pressure value.
Possible causes
- Contact resistance in the connector terminal
- Incorrect hose connection
- Damaged air pressure sensor in the intake pipe
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2Check that the hoses to the intake pipe are correctly fitted and not leaking
- 3Check that the sensor connector is fully engaged and free from oxidation and play
- 4If you have diagnostic equipment, compare the intake pressure in live data with atmospheric pressure with the ignition on
- 5If the fault remains, have a workshop check the pressure sensor in the intake pipe
Symptoms you may notice1
- No noticeable symptoms for the driver
What the fault can affect2
- The air pressure sensor signal is held at a constant value
- Load and air flow are calculated without using the sensor signal
General guidance for car owners. Diagnosis on the car can point to a different cause.