VOLVO
ECM-P010664 - Manifold Absolute Pressure/BARO Sensor Range/Performance. Algorithm Based Failures. Signal plausibility failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM measures the intake pressure with an air pressure sensor. The code is stored when the sensor reading is too low compared with the value the model calculates. The fault is thus an implausible, too-low reading from the sensor, and the control module then ignores that sensor signal for load and airflow calculations.
Possible causes
- Poor contact at the connector terminals
- Hose fitted incorrectly
- Air pressure sensor in the intake pipe has failed
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2Look for leaks and loose connections at the intake pipe hoses
- 3Check that the sensor connector is firmly seated and free from oxidation
- 4If you have diagnostic equipment, read the intake pressure in live data with the engine running; it should read lower than atmospheric pressure
- 5If the fault remains, have a workshop check the pressure sensor
Symptoms you may notice1
- No noticeable symptoms for the driver
What the fault can affect2
- The sensor signal is replaced by a constant value
- Load and air flow are calculated independently of the air pressure sensor
General guidance for car owners. Diagnosis on the car can point to a different cause.