VOLVO
ECM-P010817 - Manifold Absolute Pressure/BARO Sensor High. General Electrical Failures. Circuit voltage above threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM measures the intake pressure with an air pressure sensor and checks the sensor's DC voltage. The code is stored when an incorrect value lasts for a set time or over three or more consecutive drive cycles.
Possible causes
- Break in the signal or ground wire
- Contact resistance and oxidation in the connections
- Signal wire shorted to supply voltage
- Air pressure sensor in the intake pipe is damaged
What you can do
- 1Read and note the code, clear it and road test to see whether it returns
- 2With diagnostic equipment and the ignition on, compare the intake pressure in live data with ambient pressure; a clear difference suggests a faulty sensor
- 3Check that the connector at the sensor sits firmly and is free from oxidation and contact resistance
- 4With a multimeter, check that the signal wire is not shorted to supply voltage or ground
- 5If the fault remains and the sensor reading differs, have a workshop replace the sensor
Symptoms you may notice1
- Engine warning lamp (check engine) lit or behaving abnormally
What the fault can affect1
- The sensor signal is replaced by a constant intake air pressure value
General guidance for car owners. Diagnosis on the car can point to a different cause.