VOLVO
ECM-P020313 - Cylinder 3 Injector Circuit / Open. General Electrical Failures. Circuit open
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The fault concerns the injector on cylinder 3, which receives no signal from the control module. The circuit is checked from the earth side, and the code is set when the signal is missing.
Possible causes
- Contact resistance at the connections to the injector
- Open circuit in the signal wire
- Open circuit in the voltage supply
- Damaged injector
What you can do
- 1Read and clear the code, then start the engine to see whether it returns
- 2Check that the fuses are intact
- 3Use a multimeter to check that the wire to the injector on cylinder 3 has no break
- 4Check the connector at the injector on cylinder 3 for damage and contact resistance
- 5If the fault remains, a workshop with diagnostic equipment should check the injector on cylinder 3
Symptoms you may notice4
- The Check engine lamp lights up or behaves abnormally
- Poor performance and lack of power while driving
- The engine hesitates or surges while driving
- The engine sounds abnormal
General guidance for car owners. Diagnosis on the car can point to a different cause.