VOLVO
ECM-P022023 - Throttle/Pedal Position Switch B Circuit. General Signal Failures. Signal stuck low
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
10 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Show models by year and engine (30)
- Volvo S60 (2011–)2011–2012Engine B6304T4 only
- Volvo S60 (2011–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T4 only
- Volvo S60 (2011–)2015Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5 only
- Volvo S80 (2007–)2007Engine B6324S, B8444S only
- Volvo S80 (2007–)2008–2009Engine B6304T2, B6324S, B8444S only
- Volvo S80 (2007–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo S80 (2007–)2011–2012, 2015Engine B6304T4, B6324S4, B6324S5 only
- Volvo S80 (2007–)2013–2014Engine B5254T12, B5254T14, B6304T4, B6324S4, B6324S5 only
- Volvo V40 (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 (2013–)2015Engine B5204T8, B5204T9 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V60 (2011–)2011–2012Engine B6304T4 only
- Volvo V60 (2011–)2013Engine B5204T8, B5204T9, B6304T4 only
- Volvo V60 (2011–)2014Engine B5204T8, B5204T9, B5254T12, B6304T4 only
- Volvo V60 (2011–)2015Engine B5204T9, B5254T12, B6304T3, B6304T4, B6304T5 only
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2009Engine B6304T2, B6324S only
- Volvo V70 (2008–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo V70 (2008–)2011–2012Engine B6304T4, B6324S5 only
- Volvo V70 (2008–)2013–2014Engine B5204T9, B6304T4, B6324S5 only
- Volvo V70 (2008–)2015Engine B5204T9, B6304T4 only
- Volvo XC60 (2009–)2009Engine B6304T2 only
- Volvo XC60 (2009–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo XC60 (2009–)2011–2014Engine B6304T4, B6324S4, B6324S5 only
- Volvo XC60 (2009–)2015Engine B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5 only
- Volvo XC70 (2008–)2008Engine B6324S only
- Volvo XC70 (2008–)2009Engine B6304T2, B6324S only
- Volvo XC70 (2008–)2010Engine B6304T2, B6324S, B6324S2 only
- Volvo XC70 (2008–)2011–2015Engine B6304T4, B6324S4, B6324S5 only
- Volvo XC90 (2003–)2007–2010Engine B6324S only
What does this fault code mean?
Although the code is named switch B circuit, it applies to the signal from the accelerator pedal position sensor. The signal stays low for a longer period and therefore does not follow the pedal movement. The fault is first registered in the central electronic module (CEM), so the root fault may be there.
Possible causes
- Signal wire shorted to ground
- Damaged accelerator pedal position sensor
- Fault in the central electronic module (CEM), which registers the fault first
What you can do
- 1Read the codes in all control modules, not only the engine control module. If a code is present in the CEM, deal with it first
- 2Check that the fuses are intact. Fuse locations are shown in the owner's manual
- 3Look at the accelerator pedal connector and wiring for loose connections, corrosion and chafed areas
- 4Use a multimeter to check that the signal wire from the pedal is not shorted to ground
- 5If you have a diagnostic tool: check whether the accelerator pedal position in live data stays at the same low value when the pedal is pressed
- 6If the fault remains after these checks, have a workshop check the CEM and the accelerator pedal sensor with diagnostic equipment. The code is only cleared once the root fault is fixed
Symptoms you may notice2
- Accelerator pedal ignored during braking
- Warning symbol and message in the display
What the fault can affect1
- When the brake pedal is pressed at the same time, the accelerator is treated as released
General guidance for car owners. Diagnosis on the car can point to a different cause.