VOLVO
ECM-P023402 - Turbocharger/Supercharger A Overboost Condition. General Failure Information. General signal failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM monitors the boost pressure sensor signal. The fault is set when the signal stays above a certain value for a set time. It points to a signal fault in the sensor or its wiring.
Possible causes
- Loose contact, contact resistance or oxidation in the connections
- Signal wire shorted to voltage
- Open circuit in the signal wire
- Open circuit in the signal ground wire
- Damaged boost pressure sensor
What you can do
- 1Read the code, clear it and road test to see whether it returns
- 2With a diagnostic tool, read boost pressure in live data at idle; an unreasonably high value with the engine calm points to the sensor
- 3Check that the fuses are intact. Fuse locations are shown in the owner's manual
- 4Look at the boost pressure sensor connector for oxidation and loose connections
- 5Use a multimeter to check that the signal wire to the boost pressure sensor is not shorted to positive and that the ground wire is not broken
- 6If the fault remains, have a workshop check the boost pressure sensor with diagnostic equipment
Symptoms you may notice2
- The check engine lamp comes on or behaves abnormally
- Poor performance and lack of power while driving
General guidance for car owners. Diagnosis on the car can point to a different cause.