VOLVO
ECM-P023716 - Turbocharger/Supercharger Boost Sensor A Circuit Low. General Electrical Failures. Circuit voltage below threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) checks the boost pressure sensor signal. The fault is set when the signal stays below a certain value for a set time, and it concerns a voltage that is too low in the sensor circuit.
Possible causes
- Contact resistance or oxidation in the connections
- Signal wire shorted to ground
- Damaged boost pressure sensor
What you can do
- 1Read the code, clear it and road test to see whether it returns
- 2Look at the boost pressure sensor connector for oxidation and loose connections
- 3Use a multimeter to check that the signal wire from the boost pressure sensor is not shorted to ground
- 4Check that the fuses are intact. Fuse locations are shown in the owner's manual
- 5If the fault remains, have a workshop check the boost pressure sensor with diagnostic equipment
Symptoms you may notice2
- The check engine lamp comes on or behaves abnormally
- The car feels poor to drive, with reduced performance and lack of power
What the fault can affect1
- Boost pressure is limited
General guidance for car owners. Diagnosis on the car can point to a different cause.