VOLVO
ECM-P025A13 - Fuel Pump A Control Circuit / Open. General Electrical Failures. Circuit open
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM sets fuel pressure through the fuel pump control module using a PWM (pulse-width modulated) signal. The code is stored when the PWM signal between the ECM and the fuel pump control module is missing. It is a general electrical fault with an open circuit, which may be caused by a signal wire short-circuited to supply voltage or a damaged fuel pump control module.
Possible causes
- Signal wire short-circuited to supply voltage
- Damaged fuel pump control module
What you can do
- 1Read and note the fault code, clear it and test drive to see whether it returns
- 2If you have a diagnostic tool: activate the fuel pump with the ignition on and see whether it runs; if it does not, the fault is likely still present
- 3Check the connector to the fuel pump control module for contact resistance and oxidation
- 4With the ignition off and the connector disconnected, use a multimeter to check that the signal wire to the fuel pump control module has no open circuit or short circuit to ground
- 5Have a workshop with diagnostic equipment check the fuel pump control module and the fuel pump
Symptoms you may notice2
- The engine does not start but cranks
- The engine stalls while driving, at any time or all the time
General guidance for car owners. Diagnosis on the car can point to a different cause.