VOLVO
ECM-P027112 - Cylinder 4 Injector Circuit High. General Electrical Failures. Circuit short to battery
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM checks the circuits to the injectors and stores the code when the signal to the injector for cylinder 4 is too high. The fault is a short circuit to supply voltage, which is a general electrical fault. The code applies to cylinder 4 only.
Possible causes
- Signal wire short-circuited to supply voltage
- Damaged injector
What you can do
- 1Read and note the fault code, clear it and test drive to see whether it returns
- 2Check that the fuses are intact
- 3Check the connector to the cylinder 4 injector for contact resistance and oxidation
- 4With the ignition on and the connector disconnected, use a multimeter to check whether the signal wire to the injector has voltage to ground
- 5Have a workshop with diagnostic equipment check the injector for cylinder 4 and its control
Symptoms you may notice4
- The Check engine light comes on or behaves abnormally
- The car lacks power
- The car hesitates, surges or runs jerkily, at any time or all the time
- A noise from the engine, at any time or all the time
General guidance for car owners. Diagnosis on the car can point to a different cause.