VOLVO
ECM-P029D92 - Cylinder 1- Injector Leaking. Component Failures. Performance or incorrect operation
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM checks that each injector is functioning as it should. If an injector fails to open or close fully, misfires can result, among other things. The code is stored for cylinder 1 when the injector does not work correctly, and the fault may be that it has stuck. It is a component fault.
Possible causes
- Damaged injector
What you can do
- 1Read and note the fault code, clear it and test drive to see whether it returns
- 2If you have a diagnostic tool: with the ignition on, activate the injector a few times to free any dirt; once per cylinder and drive only
- 3Check the connector to the cylinder 1 injector for contact resistance and oxidation
- 4If the fault remains after the activation, have a workshop replace the cylinder 1 injector
Symptoms you may notice4
- The Check engine light comes on or behaves abnormally
- The car lacks power
- The car hesitates, surges or runs jerkily, at any time or all the time
- A noise from the engine, at any time or all the time
General guidance for car owners. Diagnosis on the car can point to a different cause.