VOLVO
ECM-P032616 - Knock Sensor 1 Circuit Range/Performance (Bank 1). General Electrical Failures. Circuit voltage below threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) monitors the left knock sensor signal at certain operating points. If the signal is too low under these conditions, the fault code is set. The causes may be a loose or damaged knock sensor, poor contact, a break, or signal cables that are short-circuited to each other.
Possible causes
- Loose knock sensor
- Contact resistance in the knock sensor connections
- Break in the signal cable
- Short circuit between the knock sensors' signal cables
- Damaged knock sensor
What you can do
- 1Read the fault code, clear it and test drive the car to see whether it returns
- 2Check that the left knock sensor is firmly seated
- 3Check the knock sensor connectors for contact resistance and oxidation
- 4Check the signal cables for breaks; with a multimeter, confirm that the cables have no contact with each other
- 5Have a workshop with diagnostic equipment check and, if needed, replace the damaged knock sensor
Symptoms you may notice1
- Poor performance and lack of power while driving
What the fault can affect2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
General guidance for car owners. Diagnosis on the car can point to a different cause.