VOLVO
ECM-P032815 - Knock Sensor 1 Circuit High (Bank 1). General Electrical Failures. Circuit short to battery or open
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) monitors the signal from the left knock sensor and sets the fault code when the signal is too high. This can be caused by a signal cable short-circuited to voltage or by an open circuit. An incorrectly fitted or damaged knock sensor can also produce the fault code.
Possible causes
- Signal cable short-circuited to voltage
- Incorrectly fitted knock sensor
- Damaged knock sensor
What you can do
- 1Clear the fault code and test drive the car to see whether it returns
- 2Check that the wiring to the left knock sensor is complete, with no breaks or chafing, and that the plug is firmly connected
- 3With a multimeter, confirm that the cable is unbroken and has no contact with the positive supply
- 4Check that the left knock sensor is correctly fitted
- 5Have a workshop with diagnostic equipment check the sensor and the wiring and replace the knock sensor if needed
Symptoms you may notice1
- Poor performance and lack of power while driving
What the fault can affect2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
General guidance for car owners. Diagnosis on the car can point to a different cause.