VOLVO
ECM-P033117 - Knock Sensor 2 Circuit Range/Performance (Bank 2). General Electrical Failures. Circuit voltage above threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
Under some operating conditions the ECM watches the right knock sensor output. When that output becomes too high, the fault code is set. A loose or incorrectly fitted sensor, a signal cable with a ground contact, or a damaged sensor may be the cause.
Possible causes
- Loose knock sensor
- Signal cable short-circuited to ground
- Incorrectly fitted knock sensor
- Damaged knock sensor
What you can do
- 1Read the fault code and test drive the car to see whether it returns
- 2Check that the right knock sensor is firmly seated and correctly fitted
- 3Check the signal cable from the right sensor for chafing and places where it may have touched the body; with a multimeter, confirm that the cable has no contact with ground
- 4If you have a diagnostic tool: read the knock signal from the right sensor in live data with the engine running and see whether the value is too high
- 5Have a workshop with diagnostic equipment check and, if needed, replace the knock sensor
Symptoms you may notice1
- Poor performance and lack of power while driving
What the fault can affect2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
General guidance for car owners. Diagnosis on the car can point to a different cause.