VOLVO
ECM-P033312 - Knock Sensor 2 Circuit High (Bank 2). General Electrical Failures. Circuit short to battery
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The fault concerns a signal from the right knock sensor that is too high. A signal cable short-circuited to voltage is one possible cause. An incorrectly fitted sensor can also produce the same fault code.
Possible causes
- Signal cable short-circuited to voltage
- Incorrectly fitted knock sensor
What you can do
- 1Read the fault code, clear it and test drive the car
- 2Check the signal cable from the right knock sensor where it could have touched the positive supply; with a multimeter, confirm that the cable has no contact with the positive supply
- 3Check that the right knock sensor is correctly fitted
- 4If you have a diagnostic tool: read the knock signal from the right sensor in live data with the engine running and see whether it is too high
- 5Have a workshop with diagnostic equipment check the wiring and replace the knock sensor if needed
Symptoms you may notice1
- Poor performance and lack of power while driving
What the fault can affect2
- Ignition timing is retarded as a safety measure
- Boost pressure is reduced
General guidance for car owners. Diagnosis on the car can point to a different cause.