VOLVO
ECM-P035513 - Ignition Coil E Primary/Secondary Circuit. General Electrical Failures. Circuit open
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
10 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–), XC90 (2003–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011–2012Engine B6304T4 only
- Volvo S60 (2011–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T4 only
- Volvo S60 (2011–)2015Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5 only
- Volvo S80 (2007–)2011–2012, 2015Engine B6304T4, B6324S4, B6324S5 only
- Volvo S80 (2007–)2013–2014Engine B5254T12, B5254T14, B6304T4, B6324S4, B6324S5 only
- Volvo V40 (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 (2013–)2015Engine B5204T8, B5204T9 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V60 (2011–)2011–2012Engine B6304T4 only
- Volvo V60 (2011–)2013Engine B5204T8, B5204T9, B6304T4 only
- Volvo V60 (2011–)2014Engine B5204T8, B5204T9, B5254T12, B6304T4 only
- Volvo V60 (2011–)2015Engine B5204T9, B5254T12, B6304T3, B6304T4, B6304T5 only
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2011–2012Engine B6304T4, B6324S5 only
- Volvo V70 (2008–)2013–2014Engine B5204T9, B6304T4, B6324S5 only
- Volvo V70 (2008–)2015Engine B5204T9, B6304T4 only
- Volvo XC60 (2009–)2011–2014Engine B6304T4, B6324S4, B6324S5 only
- Volvo XC60 (2009–)2015Engine B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5 only
- Volvo XC70 (2008–)2011–2015Engine B6304T4, B6324S4, B6324S5 only
- Volvo XC90 (2003–)2011–2014Engine B6324S5 only
What does this fault code mean?
Ignition coil E has an open circuit in its signal wire, according to the code. The code is stored when the open circuit persists over several driving cycles in a row, and it concerns the primary and secondary circuit of the coil.
Possible causes
- Contact resistance and oxidation in the connections
- Open circuit in the signal wire
- Damaged ignition coil
What you can do
- 1If you have a diagnostic tool, start the engine and read the fault status. 'Fault found' means the fault is permanent.
- 2Check that the fuses are intact.
- 3With the ignition off, check the connector at ignition coil E for contact resistance and oxidation.
- 4Use a multimeter to check that the signal wire to ignition coil E has no open circuit.
- 5Check that the wire to ignition coil E is not twisted, pinched or chafed.
- 6If the fault returns, have a workshop check ignition coil E and its diagnostic line.
Symptoms you may notice4
- Engine lacks power, especially when pulling away from standstill
- Car lacks power while driving
- Car hesitates or jerks during acceleration
- Car hesitates or jerks at steady speed
What the fault can affect1
- Closed loop control of lambda is blocked
General guidance for car owners. Diagnosis on the car can point to a different cause.