VOLVO
ECM-P062E09 - Fuel Injector Driver Circuit Performance Bank 2. General Failure Information. Component Failures
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
Although the fault code concerns a component fault, the condition is a current signal to the bank 2 injectors that is too low, as seen by the engine control module. It is set when the signal does not match what has been requested, and it may be due to poor contact in the injector connectors or a damaged control module.
Possible causes
- Contact resistance or oxidation in the connections
- Damaged engine control module (ECM)
What you can do
- 1Check that the connectors at the bank 2 injectors are secure and free from oxidation
- 2If you have a diagnostic tool: read the status of the code after the repair
- 3If the fault remains after these checks: have a workshop replace the control module or check it
Symptoms you may notice3
- The engine does not start, sometimes or all the time
- The engine is hard to start and the starter motor cranks slowly, sometimes or all the time
- The check engine lamp lights or behaves abnormally
General guidance for car owners. Diagnosis on the car can point to a different cause.