VOLVO
ECM-P062E17 - Fuel Injector Driver Circuit Performance Bank 2. General Electrical Failures. Circuit voltage above threshold
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
Although the fault code is named for an overvoltage, the condition is an open circuit in the wire to the injector on the supply side, detected by the output stage. It can be due to a break in the wire, a damaged connector, or looseness and oxidation in the connector. The engine may then lack power while driving.
Possible causes
- Break in the wire or a short to ground
- Damaged connector
- Loose connection, oxidation in the connector
What you can do
- 1Check that the fuses are intact
- 2With the ignition off, look at the connector at the supply-side injector for damage, looseness and oxidation
- 3With the ignition off and a multimeter, check that the wire to the injector is not broken
- 4If the fault remains: have a workshop check the wire and the connectors with diagnostic equipment
Symptoms you may notice2
- The check engine lamp lights or behaves abnormally
- The engine lacks power while driving
General guidance for car owners. Diagnosis on the car can point to a different cause.