VOLVO
ECM-P062F46 - Internal Control Module EEPROM Error. System Internal Failures. Calibration / parameter memory failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) monitors its own memory where the calibration and parameter values are stored (EEPROM). The code is set when the module finds an internal fault in that memory. The check starts when the ignition is switched on, and the fault can only be found while the test is running and the conditions are met. The timing of the symptoms is unclear, and the engine may stall or fail to start.
Possible causes
- Communication interference
- Damaged engine control module (ECM)
What you can do
- 1Switch on the ignition and wait a short while before reading the codes, so the module can complete its test
- 2Read the fault code status and check that the fault is no longer active when the test is complete
- 3Check whether other fault codes are stored in the engine control module; these should be traced first
- 4If the code returns after it has been cleared and the car has been road tested, the engine control module needs replacing; have a workshop do this
Symptoms you may notice2
- The engine may stall while driving, at an unclear moment or all the time
- The engine does not start
General guidance for car owners. Diagnosis on the car can point to a different cause.