VOLVO
ECM-P068611 - ECM/PCM Power Relay Control Circuit Low. General Electrical Failures. Circuit short to ground
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
When the ignition goes off, the system relay releases only after a set delay, which gives the control module time to finish what it is doing before power to the affected parts is removed. The code is set when the relay releases too late or too early compared with what is expected.
Possible causes
- Signal wire short-circuited to ground
- No supply voltage to the system relay
- Damaged system relay
What you can do
- 1Read and clear the fault code, and check the battery charge and that the terminals are secure
- 2Check the fuses for the system relay supply in the owner's manual
- 3Look at the wiring to the system relay for chafing, pinch damage and loose contacts, especially where it may have touched the body
- 4Use a multimeter to check that the signal wire to the system relay has no contact with ground (the body), with the connectors disconnected
- 5Check that supply voltage reaches the relay: measure at the connector with the ignition on
- 6If the fault remains after these checks, have a workshop check the system relay
Symptoms you may notice2
- The battery may appear weak
- The vehicle electrical system may have lower voltage than normal
General guidance for car owners. Diagnosis on the car can point to a different cause.