VOLVO
ECM-P069071 - ECM/PCM Power Relay Sense Circuit High. Mechanical Failures. Actuator stuck
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The code indicates a mechanical fault where the system relay has stuck and does not release as it should. The sense circuit then shows a signal that is too high to the control module.
Possible causes
- Signal wire short-circuited to ground
- Wiring from the system relay contact short-circuited to voltage
- Damaged system relay
What you can do
- 1Read and clear the fault code, and check whether it returns after a few ignition switch-offs
- 2Listen for a click from the system relay when the ignition is switched off, and note whether it is missing
- 3Check the fuses for the system relay in the owner's manual
- 4Look at the connectors and wiring to the system relay for loose contacts, oxidation and chafing
- 5Use a multimeter to check that the wiring from the system relay contact has no contact with voltage, with the connectors disconnected
- 6If the fault remains, have a workshop check the system relay and the wire to it
Symptoms you may notice1
- The battery may have low voltage
General guidance for car owners. Diagnosis on the car can point to a different cause.