VOLVO
ECM-P07BE62 - Transmission Park Position Sensor/Switch "A" / "B" Correlation. Algorithm Based Failures. Signal compare failure
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module uses signals from the transmission control module (TCM) to determine which position the selector lever is in, and thereby whether starting the engine is allowed. The code is set when the CAN signal and the signal from the directly connected wire from the selector lever do not agree.
Possible causes
- Look for the fault cause in the transmission control module (TCM)
What you can do
- 1Read and clear the fault code, and check whether it returns when you start in park
- 2Check that the selector lever is firmly seated and that you are in the correct position when starting
- 3Look at the connectors to the selector lever for loose contacts, oxidation and chafing
- 4Use a multimeter to check that the wire from the selector lever is not broken, with the connectors disconnected
- 5If the fault remains, have a workshop read the transmission control module (TCM) and check the selector lever
Symptoms you may notice1
- Starting and autostart do not work
What the fault can affect1
- The signal coming via CAN is used instead
General guidance for car owners. Diagnosis on the car can point to a different cause.