VOLVO
ECM-P083F00 - Clutch Pedal Switch A / B Correlation. General Failure Information. No sub type information
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
12 modelsC30 (2007–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V60 Cross Country (2015–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Show models by year and engine (23)
- Volvo C30 (2007–2013)2011–2013Engine D4162T only
- Volvo S40 (2004–2013)2011–2012Engine D4162T only
- Volvo S60 (2011–)2011–2012Engine B6304T4 only
- Volvo S60 (2011–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T4 only
- Volvo S60 (2011–)2015Engine B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5 only
- Volvo S80 (2007–)2008–2010Engine D4204T only
- Volvo S80 (2007–)2011–2012, 2015Engine B6304T4 only
- Volvo S80 (2007–)2013–2014Engine B5254T12, B5254T14, B6304T4 only
- Volvo V40 (2013–)2013–2014Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V40 (2013–)2015Engine B5204T8, B5204T9 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B5204T8, B5204T9, B5254T12, B5254T14 only
- Volvo V50 (2004–2013)2011–2012Engine D4162T only
- Volvo V60 (2011–)2011–2012Engine B6304T4 only
- Volvo V60 (2011–)2013Engine B5204T8, B5204T9, B6304T4 only
- Volvo V60 (2011–)2014Engine B5204T8, B5204T9, B5254T12, B6304T4 only
- Volvo V60 (2011–)2015Engine B5204T9, B5254T12, B6304T3, B6304T4, B6304T5 only
- Volvo V60 Cross Country (2015–)2015
- Volvo V70 (2008–)2008–2010Engine D4204T only
- Volvo V70 (2008–)2011–2012Engine B6304T4 only
- Volvo V70 (2008–)2013–2015Engine B5204T9, B6304T4 only
- Volvo XC60 (2009–)2011–2014Engine B6304T4 only
- Volvo XC60 (2009–)2015Engine B5204T9, B5254T12, B5254T14, B6304T4 only
- Volvo XC70 (2008–)2011–2015Engine B6304T4 only
What does this fault code mean?
The ECM compares clutch pedal switches A and B with each other, and the code is set when the signals do not agree. On cars without an electronic parking brake, an extra position switch replaces the position sensor.
Possible causes
- Damaged clutch pedal switch
- Loose contact
- Contact resistance or oxidation in connectors or connections
- Wires shorted to earth or to voltage
What you can do
- 1Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
- 2Try starting, auto-start and cruise control with the buttons and controls to see whether they are affected
- 3Check that the clutch pedal moves freely and does not stick, and that the connectors at the pedal are firmly seated
- 4Check that the connectors are free from oxidation and contact resistance, and that the cables have not chafed or been pinched
- 5Use a multimeter to check that the wires to the connectors have no contact with earth (the body) or with positive
- 6If you have a diagnostic tool, check in live data that switches A and B change state as the pedal moves. If they do not, have a workshop investigate
Symptoms you may notice2
- Starting and auto-start do not work
- Cruise control cannot be engaged
General guidance for car owners. Diagnosis on the car can point to a different cause.