Skip to content
    OBD Tuning
    Send to us
    Send to us
    Home
    Fault Codes
    VOLVO
    ECM-P08AF00
    VOLVO

    ECM-P08AF00 - Neutral Position Sensor "B" Circuit Low. General Failure Information. No sub type information

    System

    Engine Control Module (ECM)

    Volvo models this fault code applies to

    Applies to the following models:

    8 models

    S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)

    Show models by year and engine (28)
    • Volvo S60 (2011–)2011Engine B4164T, B4164T3 only
    • Volvo S60 (2011–)2012All engines except: B4204T7, B5254T5, B6304T4, D4162T
    • Volvo S60 (2011–)2013Engine B4164T, B4164T2, B4164T3, D5204T3, D5204T7, D5244T11, D5244T15 only
    • Volvo S60 (2011–)2014All engines except: B4204T7, B5204T8, B5204T9, B5254T12, B5254T14, B6304T4, D4162T
    • Volvo S60 (2011–)2015All engines except: B5204T8, B5204T9, B5254T12, B5254T14, B6304T3, B6304T4, B6304T5, D4162T
    • Volvo S80 (2007–)2011Engine B4164T only
    • Volvo S80 (2007–)2012Engine B4164T, B4164T2, D5204T3, D5244T11, D5244T15 only
    • Volvo S80 (2007–)2013Engine B4164T, B4164T2, D5204T3, D5204T7, D5244T11, D5244T15 only
    • Volvo S80 (2007–)2014All engines except: B4204T6, B4204T7, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5, D4162T
    • Volvo S80 (2007–)2015All engines except: B6304T4, B6324S4, B6324S5, D4162T
    • Volvo V40 (2013–)2013Engine B4164T, B4164T3, D5204T4, D5204T6 only
    • Volvo V40 (2013–)2014Engine B4164T, B4164T3, B4164T4, D5204T4, D5204T6 only
    • Volvo V40 (2013–)2015All engines except: B5204T8, B5204T9, D4162T
    • Volvo V40 Cross Country (2013–)2013–2014Engine B4164T, D5204T4, D5204T6 only
    • Volvo V40 Cross Country (2013–)2015Engine B4164T, B4204T11, D4204T14, D5204T6 only
    • Volvo V60 (2011–)2011Engine B4164T, B4164T3 only
    • Volvo V60 (2011–)2012All engines except: B4204T7, B6304T4, D4162T
    • Volvo V60 (2011–)2013All engines except: B4204T7, B5204T8, B5204T9, B6304T4, D4162T, D82PHEV
    • Volvo V60 (2011–)2014All engines except: B4204T7, B5204T8, B5204T9, B5254T12, B6304T4, D4162T, D82PHEV
    • Volvo V60 (2011–)2015All engines except: B5204T9, B5254T12, B6304T3, B6304T4, B6304T5, D4162T, D82PHEV, D87PHEV
    • Volvo V70 (2008–)2011Engine B4164T only
    • Volvo V70 (2008–)2012Engine B4164T, B4164T2, D5204T3, D5244T11, D5244T15 only
    • Volvo V70 (2008–)2013–2014All engines except: B4204T7, B5204T9, B6304T4, B6324S5, D4162T
    • Volvo V70 (2008–)2015All engines except: B5204T9, B6304T4, D4162T
    • Volvo XC60 (2009–)2012Engine D5204T3, D5244T11, D5244T15, D5244T17 only
    • Volvo XC60 (2009–)2013–2014All engines except: B4204T7, B6304T4, B6324S4, B6324S5
    • Volvo XC60 (2009–)2015All engines except: B4204T7, B5204T9, B5254T12, B5254T14, B6304T4, B6324S4, B6324S5
    • Volvo XC70 (2008–)2012–2015All engines except: B6304T4, B6324S4, B6324S5

    What does this fault code mean?

    The signal from neutral position sensor B is missing or too low, which points to a short to earth. The sensor has a redundancy sensor as a backup. The fault is checked with the ignition on and then with the engine running.

    Possible causes

    • Signal wire shorted to earth
    • Break in the signal wire
    • Short to earth in the connector
    • Loose contact or oxidation in the connector
    • Damaged neutral position sensor

    What you can do

    1. 1Check that the fuses are intact. The locations are shown in the instruction manual or on the fuse list
    2. 2Use a multimeter to check that the signal wire to sensor B has no break and no contact with earth (the body)
    3. 3Check that the connector at the sensor is firmly seated and free from looseness and oxidation
    4. 4Check that the wire has not rubbed against the body or an edge where it passes
    5. 5Where possible, try automatic stop-start with the buttons and controls to see whether it is affected
    6. 6If you have a diagnostic tool, check in live data that the value for sensor B does not stay too low when the gear lever is moved

    Symptoms you may notice3

    • Automatic engine stop-start does not work while driving
    • Automatic engine stop-start does not work at idle
    • Starting and auto-start do not work

    What the fault can affect1

    • The automatic engine stop-start function is switched off

    General guidance for car owners. Diagnosis on the car can point to a different cause.

    OBD Tuning

    Sweden's leading expert center for automotive electronics. We offer professional ECU tuning, control unit repair and diagnostics with 12-month warranty.

    Services

    • Engine Tuning
    • ECU Repair
    • Module Cloning
    • Instrument Cluster
    • SRS / Airbag
    • Immobilizer

    Database & Diagnostics

    • ECU Database
    • DTC Fault Code Catalog
    • Diagnostic Guides & Live Data
    • AI Fault Code Analyzer
    • News

    ECU Manufacturers

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    Company

    • About us
    • Contact
    • Workshop Partners
    • Shipping Guide
    • Warranty
    • FAQ
    • Terms & Conditions
    • Privacy Policy
    • Site Map

    • Engine Tuning
    • ECU Repair
    • Module Cloning
    • Instrument Cluster
    • SRS / Airbag
    • Immobilizer

    • ECU Database
    • DTC Fault Code Catalog
    • Diagnostic Guides & Live Data
    • AI Fault Code Analyzer
    • News

    • Bosch
    • Continental
    • Delphi
    • Delco
    • Denso
    • Magneti Marelli
    • Siemens / VDO
    • Keihin
    • Temic

    • About us
    • Contact
    • Workshop Partners
    • Shipping Guide
    • Warranty
    • FAQ
    • Terms & Conditions
    • Privacy Policy
    • Site Map

    Visit us

    Gjuterigatan 29, Karlstad

    Call us

    054-830 480

    Email us

    service@obdtuning.se

    © 2026 OBD Tuning Karlstad. All rights reserved.