VOLVO
ECM-P116922 - Fuel Rail Pressure Sensor In Range But High. General Signal Failures. Signal too high
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The ECM monitors the high pressure side of the fuel system through the pressure sensor. The code is set when fuel pressure builds up too quickly during pre-heating, or when the fuel adaptations indicate rich running under pressure above a certain level, if the block heater was not running at start.
Possible causes
- Leak in the fuel system
- Damaged fuel pressure sensor
What you can do
- 1Look for leaks on the high pressure side of the fuel system and fix any faults
- 2Check other fault codes in the control module that could affect the fuel system before replacing any part
- 3Note the engine and ambient temperatures when the fault occurs, since this helps the workshop
- 4If you find no leak or other fault codes: have a workshop replace the high pressure fuel pressure sensor
- 5If the fault returns after repair: have a workshop check the high pressure fuel pump
Symptoms you may notice3
- Idle that stalls, either occasionally or all the time
- Poor performance and lack of power while driving
- The engine is hard to start or does not start, either occasionally or all the time
General guidance for car owners. Diagnosis on the car can point to a different cause.