VOLVO
ECM-P126004 - Theft Detected, Vehicle Immobilized. General Failure Information. System Internal Failures
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) has no code for the immobilizer or has an internal fault. Before the engine starts, the immobilizer code in the ECM is compared with the one in the central electronic module (CEM). The code is set when the ECM is not programmed or when an internal fault is detected in the module.
Possible causes
- The ECM has not been programmed and holds no immobilizer code
- Damaged engine control module (ECM)
What you can do
- 1Check that the fuses are intact. The locations are in the owner's manual or on the fuse box cover.
- 2Check that the connectors to the engine control module are secure and free from corrosion.
- 3Have a workshop program the engine control module (ECM), as this requires special equipment.
- 4If the engine control module is damaged it must be replaced, which is also a workshop job.
- 5After the work: switch the ignition off, reconnect the connectors and components, start the engine and read the code again.
Symptoms you may notice1
- The engine does not start and does not turn over
General guidance for car owners. Diagnosis on the car can point to a different cause.