VOLVO
ECM-P133695 - Crankshaft/Camshaft Sensor Range/Performance. Component Failures. Incorrect assembly
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The code concerns the position of the intake camshaft relative to the crankshaft. The engine control module (ECM) compares the camshaft position with the crankshaft position and sets the code when the camshaft is incorrectly adjusted after a timing belt change. The fault is noticed at start attempts, when the engine is to be started.
Possible causes
- Incorrectly adjusted camshaft after timing belt replacement
- Incorrectly installed camshaft
- Damaged camshaft
What you can do
- 1Remember that a camshaft adaption is a workshop task, and it should be done first when camshaft faults are stored.
- 2If you have a diagnostic tool, read the code before and after the workshop work, so you can see whether the fault has gone.
- 3If the timing belt was recently replaced, tell the workshop, since a camshaft set wrongly after a belt change can cause the fault.
- 4If the fault remains, have a workshop check that the intake camshaft is correctly fitted and undamaged.
Symptoms you may notice2
- The Check engine (malfunction) lamp comes on or behaves abnormally
- The engine does not start, and when the fault shows is unclear
General guidance for car owners. Diagnosis on the car can point to a different cause.