VOLVO
ECM-P177487 - CAN Link Gear Shift Module / TCM. Bus Signal / Message Failures. Missing message
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
The engine control module (ECM) waits for the start lock signal from the transmission control module (TCM) over the CAN network, and the fault code is set if the signal does not arrive within a set time. The fault is probably linked to a more general CAN fault, which is often the cause of this code as well.
Possible causes
- Fault on the CAN network
What you can do
- 1Read off the fault codes in the engine control module. If any of the codes ECM-U012088, ECM-U000188, ECM-U1A1400, ECM-U000108 or ECM-U000100 are stored, troubleshoot that one first
- 2Read off the fault codes in the transmission control module (TCM) and troubleshoot any codes there first
- 3Check that the connectors in the CAN network are firmly seated and free from oxide
- 4If the fault code returns after the other CAN faults have been fixed: have a workshop check the communication between the engine control module and the transmission control module
Symptoms you may notice1
- Starting or autostart does not work
General guidance for car owners. Diagnosis on the car can point to a different cause.