VOLVO
ECM-P193485 - Vehicle Speed Signal. Bus Signal / Message Failures. Signal above allowable range
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
7 modelsS60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V60 (2011–), V70 (2008–), XC60 (2009–)
Show models by year and engine (20)
- Volvo S60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo S60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo S60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo S80 (2007–)2010Engine B4204T6 only
- Volvo S80 (2007–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo S80 (2007–)2012–2014Engine B4164T, B4164T2, B4204T6, B4204T7 only
- Volvo S80 (2007–)2015Engine B4164T only
- Volvo V40 (2013–)2013Engine B4164T, B4164T3 only
- Volvo V40 (2013–)2014–2015Engine B4164T, B4164T3, B4164T4 only
- Volvo V40 Cross Country (2013–)2013–2015Engine B4164T only
- Volvo V60 (2011–)2011Engine B4164T, B4164T3, B4204T6, B4204T7 only
- Volvo V60 (2011–)2012–2014Engine B4164T, B4164T2, B4164T3, B4204T7 only
- Volvo V60 (2011–)2015Engine B4164T, B4164T2, B4164T3 only
- Volvo V70 (2008–)2010Engine B4204T6 only
- Volvo V70 (2008–)2011Engine B4164T, B4204T6, B4204T7 only
- Volvo V70 (2008–)2012–2014Engine B4164T, B4164T2, B4204T7 only
- Volvo V70 (2008–)2015Engine B4164T, B4164T2 only
- Volvo XC60 (2009–)2010Engine B4204T6 only
- Volvo XC60 (2009–)2011–2012Engine B4204T6, B4204T7 only
- Volvo XC60 (2009–)2013–2015Engine B4204T7 only
What does this fault code mean?
Although the code is named signal above allowable range, it applies when the speed value from the brake control module (BCM) does not change as it should for too long. The engine control module (ECM) monitors the signal and sets the code when it stays unchanged. The fault can only be detected when driving under certain conditions, and the code is stored in the BCM first and then in the ECM.
Possible causes
- Fault in the speed value from the brake control module (BCM), where the cause should be looked for
What you can do
- 1Read off the codes in the brake control module (BCM) first and remedy them
- 2Clear the code in the engine control module only once the code in the brake control module has been cleared and the fault remedied
- 3Check the connectors and wiring to the brake control module for play, corrosion and damage
- 4If you have a diagnostic tool: check in live data that the speed value from the brake control module changes when the car is moving
- 5Test drive the car after the repair, as the fault is only tested when driving under certain conditions
Symptoms you may notice1
- Check engine warning lamp lights or behaves abnormally
General guidance for car owners. Diagnosis on the car can point to a different cause.