VOLVO
ECM-P213886 - Throttle/Pedal Position Sensor/Switch D / E Voltage Correlation. Bus Signal / Message Failures. Signal invalid
System
Engine Control Module (ECM)
Volvo models this fault code applies to
Applies to the following models:
12 modelsC30 (2007–2013), C70 (2006–2013), S40 (2004–2013), S60 (2011–), S80 (2007–), V40 (2013–), V40 Cross Country (2013–), V50 (2004–2013), V60 (2011–), V70 (2008–), XC60 (2009–), XC70 (2008–)
Show models by year and engine (40)
- Volvo C30 (2007–2013)2011–2013Engine D5204T, D5204T5 only
- Volvo C70 (2006–2013)2011Engine D5204T, D5204T5 only
- Volvo C70 (2006–2013)2012–2013All engines except: B5254T7
- Volvo S40 (2004–2013)2011–2012Engine D5204T, D5204T5 only
- Volvo S60 (2011–)2011Engine D5204T2, D5244T10 only
- Volvo S60 (2011–)2012Engine D5204T3, D5244T11, D5244T15 only
- Volvo S60 (2011–)2013–2014Engine D5204T3, D5204T7, D5244T11, D5244T15 only
- Volvo S60 (2011–)2015Engine D5204T3, D5204T7, D5244T11, D5244T15, D5244T23 only
- Volvo S80 (2007–)2009Engine D5244T10 only
- Volvo S80 (2007–)2010Engine D5244T10, D5244T14, D5244T19 only
- Volvo S80 (2007–)2011Engine D5204T2, D5244T10 only
- Volvo S80 (2007–)2012Engine D5204T3, D5244T11, D5244T15 only
- Volvo S80 (2007–)2013–2014Engine D5204T3, D5204T7, D5244T11, D5244T15 only
- Volvo S80 (2007–)2015Engine D5204T3, D5244T15 only
- Volvo V40 (2013–)2013–2014Engine D5204T4, D5204T6 only
- Volvo V40 (2013–)2015Engine D5204T6 only
- Volvo V40 Cross Country (2013–)2013–2014Engine D5204T4, D5204T6 only
- Volvo V40 Cross Country (2013–)2015Engine D5204T6 only
- Volvo V50 (2004–2013)2011–2012Engine D5204T, D5204T5 only
- Volvo V60 (2011–)2011Engine D5204T2, D5244T10 only
- Volvo V60 (2011–)2012Engine D5204T3, D5244T11, D5244T15 only
- Volvo V60 (2011–)2013Engine D5204T3, D5204T7, D5244T11, D5244T15, D5244T17, D82PHEV only
- Volvo V60 (2011–)2014Engine D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D82PHEV only
- Volvo V60 (2011–)2015Engine D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23, D82PHEV, D87PHEV only
- Volvo V70 (2008–)2009Engine D5244T10 only
- Volvo V70 (2008–)2010Engine D5244T10, D5244T14, D5244T19 only
- Volvo V70 (2008–)2011Engine D5204T2, D5244T10 only
- Volvo V70 (2008–)2012Engine D5204T3, D5244T11, D5244T15 only
- Volvo V70 (2008–)2013Engine D5204T3, D5204T7, D5244T11, D5244T15, D5244T17 only
- Volvo V70 (2008–)2014–2015Engine D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17 only
- Volvo XC60 (2009–)2010Engine D5244T10, D5244T14, D5244T16 only
- Volvo XC60 (2009–)2011Engine D5204T2, D5244T10, D5244T16 only
- Volvo XC60 (2009–)2012Engine D5204T3, D5244T11, D5244T15, D5244T17 only
- Volvo XC60 (2009–)2013All engines except: B4204T7, B6304T4, B6324S4, B6324S5
- Volvo XC60 (2009–)2014Engine D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17 only
- Volvo XC60 (2009–)2015Engine D5204T3, D5204T7, D5244T11, D5244T12, D5244T15, D5244T17, D5244T23 only
- Volvo XC70 (2008–)2010Engine D5244T10, D5244T14, D5244T16 only
- Volvo XC70 (2008–)2011Engine D5204T2, D5244T10, D5244T16 only
- Volvo XC70 (2008–)2012–2013All engines except: B6304T4, B6324S4, B6324S5
- Volvo XC70 (2008–)2014–2015Engine D5204T3, D5244T11, D5244T12, D5244T15, D5244T17 only
What does this fault code mean?
The engine control module (ECM) compares the PWM signal with the analogue signal from the pedal sensor, and the code is set when the difference between them becomes too great. The fault may lie in the pedal sensor, its connectors, the ground wire or the wires of the CAN network.
Possible causes
- Poor contact or oxidation in the pedal sensor connections
- Open circuit in the ground wire or the signal ground wire
- Fault in the pedal sensor PWM signal
- Fault in the pedal sensor analogue signal
- Damaged accelerator pedal sensor
- Open or short circuit between the CAN network wires
What you can do
- 1Check that the fuses are intact; their locations are in the owner's manual or on the fuse box cover
- 2Check the connectors at the pedal sensor and the engine control module for contact resistance and oxidation, and make sure none is loose
- 3Use a multimeter to check that the ground lead to the pedal sensor has no open circuit
- 4With a diagnostic tool, read the pedal value in live data while the pedal is pressed and released, and check that it follows the movement
- 5Have a workshop with diagnostic equipment check the CAN network wires for open circuit and short circuit
- 6Replace the pedal sensor first only if the other checks show no other fault
Symptoms you may notice3
- Yellow warning symbol and a message in the display
- The car lacks power
- The engine hesitates, surges or runs jerkily during acceleration or deceleration
What the fault can affect1
- Engine output may be limited
General guidance for car owners. Diagnosis on the car can point to a different cause.